nach oben

Metallography, Microstructure, and Analysis

29.04.2024 | Original Research Article

Influence of Post-weld Heat Treatment on Microstructure and Corrosion Behavior of Dissimilar Friction Welded Joint of IN713LC Superalloy and AISI 4140 Steel

verfasst von: Vijay T. Gaikwad, M. K. Mishra, R. K. P. Singh

Erschienen in: Metallography, Microstructure, and Analysis

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

In the present work, effect of post-weld heat treatment (PWHT) on the microstructure, hardness, and corrosion behavior of friction welded IN713LC superalloy and AISI 4140 steel joint was investigated. Microstructural characterization was performed using optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD) techniques. The microstructure near weld interface (WI)/thermo-mechanically affected (TMAZ) region of IN713LC was changed from coarse dendritic structure to fine equiaxed grains. Due to dynamic recrystallization (DRX), as compared to base materials, increase in fraction of high-angle grain boundary (HAGB) and decrease in fraction of low-angle grain boundary (LAGB) were observed in WI/TMAZ (both as-welded and PWHT samples). Lath martensite was observed at WI/TMAZ of AISI 4140 steel of as-welded specimen; however, after PWHT, it transformed into the tempered martensite. The electrochemical corrosion behavior was evaluated using potentiodynamic polarization tests in 3.5 wt. % NaCl solution. Result showed that corrosion resistance of welded joint was higher than that of AISI 4140 steel and reduced after PWHT.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

W. Li, A. Vairis, M. Preuss, T. Ma, Linear and rotary friction welding review. Int. Mater. Rev. 61, 71–100 (2016)CrossRef

C.R. Arganis-Juarez, J.A. Aguilar-Torres, J.H. Ramirez-Ramírez, F.A. Perez-Gonzalez, N.F. Garza-Montes-de-Oca, R. Colas, Characterization of dissimilar welds of carbon steels and Ni-filler alloy. Metallogr. Microstruct. Anal. 12, 634–644 (2023)CrossRef

G. Baxevanis, F. Siokos, A. Kaldellis, D. Ioannidou, V. Stergiou, P. Skarvelis, P.E. Tsakiridis, Effect of post-weld heat treatment on hardness and corrosion resistance of dissimilar electron beam welded joints of Inconel 713LC and AISI 4140 steel. J. Mater. Eng. Perform. 5, 1–13 (2023)

A. Mirak, B. Shams, S. Bakhshi, Dissimilar welding of Inconel 713 superalloy and AISI 4140 steel using Nd:YAG pulse laser: an investigation on the microstructure and mechanical properties. Opt. Laser Technol. 152, 108143 (2022)CrossRef

R.R. Ye, H.Y. Li, R.G. Ding, T.J.A. Doel, S. Bray, A. Walpole, P. Bowen, Microstructure and microhardness of dissimilar weldment of Ni-based superalloys IN718-IN713LC. Mater. Sci. Eng. A. 774, 138894 (2020)CrossRef

J. Dupont, J. Lippold, S. Kiser, Welding metallurgy and weldability of nickel-base alloys (Wiley, New York, 2011)

M. Bayrak, F. Ozturk, M. Demirezen, Z. Evis, Analysis of tempering treatment on material properties of DIN 41Cr4 and DIN 42CrMo4 steels. J. Mater. Eng. Perform. 16, 597–600 (2007)CrossRef

M. Afshari, F. Taher, M.R. Samadi, M. Ayaz, Optimizing the mechanical properties of weld joint in laser welding of GTD-111 superalloy and AISI 4340 steel. Opt. Laser Technol. 156, 108537 (2022)CrossRef

X.B. Liu, G. Yu, M. Pang, J.W. Fan, H.H. Wang, C.Y. Zheng, Dissimilar autogenous full penetration welding of superalloy K418 and 42CrMo steel by a high power CW Nd:YAG laser. Appl. Surf. Sci. 253, 7281–7289 (2007)CrossRef

10.

K. Han, H. Wang, B. Zhang, J. Zhao, J. Lei, X. Zhao, Microstructural/mechanical characterizations of electron beam welded IN738LC joint after post-weld heat treatment. J. Mater. Res. Technol. 17, 1030–1042 (2022)CrossRef

11.

T. Saju, M. Velu, Characterization of welded joints of dissimilar nickel-based superalloys by electron beam and rotary friction welding. J. Mater. Eng. Perform. 31, 9462–9480 (2022)CrossRef

12.

Y. Ding, G. You, H. Wen, P. Li, X. Tong, Y. Zhou, Microstructure and mechanical properties of inertia friction welded joints between alloy steel 42CrMo and cast Ni-based superalloy K418. J. Alloys Compd. 803, 176–184 (2019)CrossRef

13.

N. Cavusoglu, Effect of friction welding parameters on the mechanical and microstructural properties of dissimilar IN713C-AISI 4140 joints. J. Mater. Eng. Perform. 31, 4035–4048 (2022)CrossRef

14.

J. Luo, L. Li, Y. Dong, X. Xu, A new current hybrid inertia friction welding for nickel-based superalloy K418-alloy steel 42CrMo dissimilar metals. Int. J. Adv. Manuf. Technol. 70, 1673–1681 (2014)CrossRef

15.

V.T. Gaikwad, M.K. Mishra, V.D. Hiwarkar, R.K.P. Singh, Microstructure and mechanical properties of friction welded carbon steel (EN24) and nickel-based superalloy (IN718). Int. J. Miner. Metall. Mater. 28, 111–119 (2021)CrossRef

16.

P. Anitha, M.C. Majumder, V. Saravanan, S. Rajakumar, Microstructural characterization and mechanical properties of friction-welded IN718 and SS410 dissimilar joint. Metallogr. Microstruct. Anal. 7, 277–287 (2018)CrossRef

17.

S.V. Lalam, G.M. Reddy, T. Mohandas, M. Kamaraj, B.S. Murty, Continuous drive friction welding of Inconel 718 and EN24 dissimilar metal combination. Mater. Sci. Technol. 25, 851–861 (2009)CrossRef

18.

M.A. Derakhshi, J. Kangazian, M. Shamanian, Electron beam welding of Inconel 617 to AISI 310: Corrosion behavior of weld metal. Vacuum. 161, 371–374 (2019)CrossRef

19.

ASTM International G5-14. Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements. ASTM Int. 1- 8 (2018)

20.

R.C. Reed, The superalloys: fundamentals and applications (Cambridge University Press, Cambridge, 2008)

21.

V.T. Gaikwad, M.K. Mishra, V.D. Hiwarkar, R.K.P. Singh, Role of friction time on the joint characteristics of continuous drive friction-welded Inconel 718 and EN24 steel. J. Mater. Eng. Perform. 32, 1660–1670 (2023)CrossRef

22.

M.K. Mishra, A.G. Rao, I. Balasundar, B.P. Kashyap, N. Prabhu, On the microstructure evolution in friction stir processed 2507 super duplex stainless steel and its effect on tensile behaviour at ambient and elevated temperatures. Mater. Sci. Eng. A. 719, 82 (2018)CrossRef

23.

E.B. Caldona, A.C.C. de Leon, J.D. Mangadlao, K.J.A. Lim, B.B. Pajarito, R.C. Advincula, On the enhanced corrosion resistance of elastomer-modified polybenzoxazine/graphene oxide nanocomposite coatings. React. Funct. Polym. 123, 10–19 (2018)CrossRef

24.

Y.B. Guo, C. Li, Y.-C. Liu, L.-M. Yu, Z.-Q. Ma, C.-X. Liu, H.-J. Li, Effect of microstructure variation on the corrosion behavior of high-strength low-alloy steel in 35 wt.% NaCl solution. Int. J. Miner. Metall. Mater. 22, 604–612 (2015)CrossRef

25.

T. Datta, A.D. Pathak, S. Basak, S. Gollapudi, K.K. Sahu, Fractal behavior of surface oxide crack patterns on AISI 4140 high-strength low-alloy steel exposed to the simulated offshore environment. Appl. Surf. Sci. Adv. 5, 100110 (2021)CrossRef

Titel: Influence of Post-weld Heat Treatment on Microstructure and Corrosion Behavior of Dissimilar Friction Welded Joint of IN713LC Superalloy and AISI 4140 Steel
verfasst von: Vijay T. Gaikwad
M. K. Mishra
R. K. P. Singh
Publikationsdatum: 29.04.2024
Verlag: Springer US
Erschienen in: Metallography, Microstructure, and Analysis
Print ISSN: 2192-9262
Elektronische ISSN: 2192-9270
DOI: https://doi.org/10.1007/s13632-024-01073-2

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht